manualshive.com logo in svg

Land Pride RCM3615, Руководство оператора

Поделиться
Скачать
Land Pride RCM3615 Скачать руководство пользователя страница 54

Section 5: Maintenance & Lubrication

RC3615 and RCM3615 Series 2 S/N Rotary Cutters 330-502M

12/12/18

50

Table of Contents

Gearbox

Method 1:

 Unscrew top vented dipstick (#1). Wipe oil 

from dipstick and screw dipstick in without tightening. 
Unscrew dipstick and check oil on dipstick. If below 
bottom level mark, add recommended gear lube through 
dipstick hole until oil reaches top mark on dipstick. 
Reinstall vented dipstick and tighten.

Method 2:

 Remove side oil plug (#2). If oil is below 

bottom of plug hole, add recommended gear lube 
through top dipstick hole until oil flows out of side plug 
hole. Reinstall and tighten side oil plug (#2) and vented 
dipstick (#1).

Type of Lubrication: 80-90W EP Gear Lube 

Quantity = Fill until oil reaches top mark on dipstick or 
begins to flow out side plug hole in gearbox

.

IMPORTANT: 

Do not overfill gearbox with oil. Oil will 

expand when hot. Make sure implement is level and 
oil is cool before checking oil level.

Divider Box

Instructions:

 Remove oil level plug. If oil is below bottom 

of plug hole, add recommended gear lube through oil 
fill/vent plug hole until oil flows out of oil level plug hole. 
Reinstall and tighten oil level plug and oil fill/vent plug.

Type of Lubrication: 80-90W EP

Quantity = Fill until oil begins to flow out oil level plug hole 
in gearbox.

IMPORTANT: 

Do not overfill gearbox with oil. Oil will 

expand when hot. Make sure implement is level and 
oil is cool before checking oil level.

If oil has been removed from the gearbox, refill 
gearbox to plug level or full mark on the dipstick. 
Allow time for air to bleed up from the lower cavity, 
and then recheck.

30215

Do Not Overfill

NOTE:  

Use a suction or siphon pump to drain 

gearbox of oil when there is not an oil drain plug.

39463

8

Hours

8

Hours

Содержание RCM3615

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды