Land Pride RCM3615 Скачать руководство пользователя

Страница: 30 / 64

Section 1: Assembly & Set-up

RC3615 and RCM3615 Series 2 S/N Rotary Cutters 330-502M

12/12/18

Table of Contents

Unhook Rotary Cutter

See

“Long-Term Storage”

on page 47 when storing

the cutter for long periods and at end of season.

2. If power take-off is engaged, reduce tractor engine

speed to an idle and then disengage power take-off.

3. Park cutter on a level, hard surface. Place tractor

gear selector in park or set park brake.

Refer to Figure 1-26:

4. Wait for blades to come to a complete stop and then

fold wings up to transport position.

5. Shut tractor engine off and remove switch key before

dismounting from tractor.

6. Remove hairpin cotter (#1) from storage lugs (#2).

Refer to Figure 1-27:

Swing transport lock bars (#3) down and place over
lock pins (#4). Secure with hairpin cotters (#1).

Refer to Figure 1-28:

8. Spread stroke control spacers (#2) apart at the break

line and remove them from hydraulic cylinder (#1).

9. Start tractor and lower cutter until front skids are

resting on the ground or on support blocks.

10. Without changing deck lift height, shut tractor down

properly before dismounting. Refer to

“Tractor

Shutdown Procedure”

on page 14.

11. Replace stroke control spacers as needed to support

wheels at this position.

12. Move cylinder lift levers back and forth to release all

hydraulic pressure at the couplers.

Transport Bar, Storage Position

Figure 1-26

Transport Bar, Locked Position

Figure 1-27

Hydraulic Lift Cylinder With Stroke Control Spacers

Figure 1-28

27923

27921

37907

Содержание RCM3615

































































Результаты поиска

Содержание RCM3615

Отзывы:

Похожие инструкции для RCM3615

Бренды по названию

Популярные бренды

Land Pride RCM3615, Руководство оператора

Результаты поиска

Содержание RCM3615

Отзывы:

Похожие инструкции для RCM3615

Бренды по названию

Популярные бренды