Land Pride RCM3615 Скачать руководство пользователя

Страница: 20 / 64

Section 1: Assembly & Set-up

RC3615 and RCM3615 Series 2 S/N Rotary Cutters 330-502M

12/12/18

Table of Contents

LP Performance Hitch Hook-up

DANGER

To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking

implement. Keep people and animals away while backing-up

to implement or pulling away from implement. Do not operate

hydraulic controls while a person or animal is directly behind

the power machine or near the implement.

WARNING

To avoid serious injury or death:
The ball detent pin must be fully inserted into the park jack

with ball visible and popped out on the far side of the jack

before working on or around an unhooked cutter.

Refer to Figure 1-9:

Make certain park jack (#3) is properly attached to
the cutter hitch and secured with ball detent pin (#8).

2. Adjust park jack angle if it is not vertical. Refer to

“Park Jack Angle Alignment”

on page 28.

3. If clevis hitch is not already supported horizontal,

rotate clevis (#9) horizontal and flip hitch holder (#11)
up so that its holes are on top as shown.

4. Insert customer-supplied hitch pin (#1) through holes

in hitch holder (#11) as shown in detail A. Secure with
hairpin cotter (#2).

5. Store center 3-point link in the tractor’s storage hook.

6. Start tractor, raise 3-point arms fully up, and carefully

back tractor within close proximity of clevis (#9).

Shut tractor down properly before dismounting. Refer
to

“Tractor Shutdown Procedure”

on page 14.

NOTE:

Hitch pin (#1) and hairpin cotter (#2) are

customer-supplied.

8. Verify tractor drawbar is adjusted correctly. Refer to

“Drawbar Set-up”

dimensions on page 12.

9. Raise or lower park jack (#3) to align clevis (#9) with

tractor drawbar. Drawbar should fit between lower
and upper plates of clevis.

10. Restart tractor and continue to back tractor up to

cutter hitch until holes in tractor drawbar and clevis
hitch (#9) are aligned.

11. Shut tractor down properly before dismounting.

12. Remove bushings in clevis if customer supplied hitch

pin diameter is larger than 1". See

“LP Performance

Hitch Pin Diameter”

on page 30 for instructions.

13. Remove hairpin cotter (2) and hitch pin (#1) from

hitch holder (#11) and rotate hitch holder down.

14. Attach cutter to tractor drawbar with hitch pin (#1) and

hairpin cotter (#2) as shown in detail B.

15. Lower park jack (#3) until hitch weight is supported

by tractor drawbar.

16. Remove park jack (#3) from hitch and attach it to the

left-hand wing storage base with detent pin (#8).
Make sure jack base is level or lower than the jack
crank head especially after the wings are folded up.
See cover picture for correct positioning.

17. Attach hitch safety chain (#4) to the tractor. Adjust

chain length to remove all slack except what is
necessary to permit turning. Lock chain hook
securely to the safety chain.

18. Continue with

“Hydraulic Hook-up”

on page 18.

IMPORTANT:

Protect park jack by storing it on the

left wing deck before moving the cutter. Make sure
jack is stored with its base level or lower than the
head to prevent water and freeze damage.

LP Performance Hitch Hook-up

Figure 1-9

37298

37631

Содержание RCM3615

































































Результаты поиска

Содержание RCM3615

Отзывы:

Похожие инструкции для RCM3615

Бренды по названию

Популярные бренды

Land Pride RCM3615, Руководство оператора

Результаты поиска

Содержание RCM3615

Отзывы:

Похожие инструкции для RCM3615

Бренды по названию

Популярные бренды