manualshive.com logo in svg

Land Pride RCM3615, Руководство оператора

Поделиться
Скачать
Land Pride RCM3615 Скачать руководство пользователя страница 34

Section 2: Adjustments

RC3615 and RCM3615 Series 2 S/N Rotary Cutters 330-502M

12/12/18

30

Table of Contents

Adjust Deck Cutting Height

Refer to Figure 2-5:

1.

At the cutting site, unfold wings and raise center deck 
fully up with lift cylinder.

2. Shut tractor down properly before dismounting. Refer 

to 

“Tractor Shutdown Procedure” 

on page 14.

Set Deck Height With Stroke Control Spacers

Figure 2-5

3. Remove all stroke control spacers (#2) from center 

hydraulic cylinder (#1) by spreading them apart at 
the break line. Store spacers in a location they can be 
retrieved.

4. Start tractor and engage blades. See 

“Engage 

Blades” 

on page 35 for detailed instructions. 

5. Using tractor control lever, adjust cutter to the desired 

cutting height and then travel forward for 
approximately 20 to 50 feet.

6. Stop tractor, disengage power take-off, place tractor 

gear selector in park or set park brake, shut off 
tractor, remove key, and wait for blades to come to a 
complete stop before dismounting from tractor.

7.

Measure height of cut grass/material. This distance 
is the cutting height. If this height is acceptable, 
continue with step 8. If this height is unacceptable, 
repeat steps 4-7 until desired cutting height is 
achieved.

8. Select required size and number of stroke control 

spacers (#2) that will fit on the center hydraulic 
cylinder rod. The following spacers are available.

•

Two 1" spacers

•

One 1 1/4" spacer

•

One 1 1/2" spacer

•

One 1 3/4" spacer 

NOTE:  

Make all cutting height adjustments in the 

field using height of cut grass/material as a guide. 
Do not measure blade height above ground as the 
non-operating blade height will be different than the 
operating blade height. 

37907

NOTE:  

Removing spacers lowers cutting height and 

adding spacers raises cutting height.

9. Return to tractor and raise Rotary Cutter up again. 

10. Without lowering the cutter, shut tractor down 

properly before dismounting. Refer to 

“Tractor 

Shutdown Procedure” 

on page 14.

11. With tractor shut off and switch key removed, install 

selected stroke control spacers on the center 
hydraulic lift cylinder rod.

12. Restart tractor and lower cutter against stroke control 

spacers. 

13. Recheck cutting height using steps 4-7 above. If 

needed, adjust size and quantity of stroke control 
spacers until desired cutting height is achieved. 

14. Keep remaining spacers with tractor for field 

adjustments.

LP Performance Hitch Pin Diameter

Refer to Figure 2-6:

The LP Performance hitch is designed to receive 
1" diameter hitch pins. To convert the hitch to receive 
1 1/4" diameter hitch pins, knock out upper and lower 
bushings (#1) in clevis (#2).

LP Performance Hitch Hole Diameter

Figure 2-6

39093

Содержание RCM3615

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды