manualshive.com logo in svg

lancer CENTURION II 85-0056, Инструкция по установке и обслуживанию

Поделиться
Скачать
lancer CENTURION II 85-0056 Скачать руководство пользователя страница 26

22

Figure 4 - Pushbutton Assembly - Part Number 82-0482

ITEM

PART NO.

DESCRIPTION

1

10-0195

Knob

2

03-0135

Spring

3

10-0196

Adaptor

4

06-0345

Label

5

REF

Front Cover

ITEM

PART NO.

DESCRIPTION

6

04-0420

Washer

7

10-0198

Nut

8

03-0086

Retainer

9

82-1014

Shaft Assembly

10. CENTURION II PUSHBUTTON SERVE/FLUSH SWITCH INSTALLATION

10.1 INSTALLATION

A. Turn key switch 

OFF

.

B. Loosen the two (2) captive screws on control panel and partially pull control panel out of the 

control housing.

C. Disconnect the transformer power cord connector inside the control housing.
D. Disconnect wiring harness by grasping the ends of the 16-pin connector on the PCB.  

Do 

NOT

remove by pulling on the wires.

E. Remove control panel from control housing.
F. Disconnect the 4 pin mode switch connector and 2-pin transformer connector by grasping the

housing.  

Do 

NOT

try to remove by pulling the wires.

G. Use a straight slot screwdriver to turn the four (4) plastic latches 1/4 turn counter clockwise and

lift the control PCB off the stand-offs.

H. Remove the eight (8) screws securing the transformer and control PCB mounting plate to the

front panel.

I.

Record the wire color and terminal position of the mode switch harness to ensure installation will
be correct.

J. Remove the two (2) 0.110 inch FAST-ON connectors from the back of the mode switch.
K. Remove the securing nut from the back of the switch and push the switch through the front of

the control panel.

L. Install new switch (PN 12-0087) provided with the kit.
M. To reassemble, reverse above procedure.

Содержание CENTURION II 85-0056









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды