manualshive.com logo in svg

lancer CENTURION II 85-0056, Инструкция по установке и обслуживанию

Поделиться
Скачать
lancer CENTURION II 85-0056 Скачать руководство пользователя страница 23

(7.22 continued)

C. Improper or loose wiring.

C. Correct wiring.  Refer to wiring

diagram.

D. Starting relay defective.

D. Replace starting relay.  Be sure

to use correct relay.  Failure to

use correct relay will cause

compressor failure.

E. Defective compressor.

E. Replace compressor.

7.23 Compressor starts and

A. Improper or loose wiring.

A. Correct wiring.  Refer to wiring

runs a short time, but

diagram.

shuts off on overload.

B. Low voltage.

B. Measure voltage across common

and run terminal on compressor.

Voltage must not drop below 90%

of rated voltage.

C. Excessively high refrigerant

C. 1. Defective condenser fan

high side pressure and

motor.  Replace.

suction return gas hot.

2. Dirty condenser.  Clean.

3. Dirty intake air filter.  Clean.

4. Back of unit too close to wall.

Move unit away from wall at

least two (2) inches (5.08 cm).

D. Compressor running too hot.

D. Refrigerant leak.  Repair and

recharge.

E. Defective compressor.

E. Replace compressor.

19

TROUBLE

CAUSE

REMEDY

Содержание CENTURION II 85-0056









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды