manualshive.com logo in svg

lancer CENTURION II 85-0056, Инструкция по установке и обслуживанию

Поделиться
Скачать
lancer CENTURION II 85-0056 Скачать руководство пользователя страница 18

6.19 FRONT COVER

CAUTION

CARE SHOULD BE USED WHEN HANDLING FRONT COVER NOT TO SCRATCH OR MAR 
SURFACE.  WHEN CLEANING USE ONLY DAMP CLEAN CLOTH.
A. Lift front cover up so that it rests on top cover.
B. Loosen two (2) wing nuts (

DO 

NOT

REMOVE

) holding retainer to front edge of top cover.

C. Slide retainer down.
D. Pull front cover forward and remove.
E. To reassemble, reverse above procedure.

6.20 TOP COVER

A. Flush both sides of unit.
B. Turn key switch 

OFF

.

C. Remove both lids.
D. Remove front cover.
E. Remove check valves from concentrate tubes.
F. Remove concentrate containers.
G. Loosen three (3) screws (

DO 

NOT

REMOVE

) holding top cover to frame 

at front

of unit.

H. Loosen three (3) screws (

DO 

NOT

REMOVE

) holding top cover to frame 

at rear

of unit.

I.

Lift top cover up and off unit.

J. To reassemble, reverse above procedure.

6.21 WRAPPER

WARNING

DISCONNECT THE POWER CORD FROM THE ELECTRICAL OUTLET.

A. Remove front cover (refer to Section 6.19) and top cover (refer to Section 6.20).
B. Remove drip tray, dispensing paddles and splash plate.
C. Remove eight (8) screws on front of unit [four (4) on each side].  Locations are as follows.

1. Top and bottom in flange of control housing.
2. Two (2) in wrapper below pump support.

NOTE

It is not necessary to remove control housing and pump support when removing wrapper.

D. Spread wrapper at front of unit slightly on each side in order to clear frame.  Push wrapper

toward back of unit until wrapper is free of frame.

CAUTION

CLEAN WRAPPER ONLY WITH DAMP CLEAN CLOTH, OR APPROVED NON-ABRASIVE SPRAY
OR LIQUID STAINLESS STEEL CLEANER.
E. To reassemble, reverse above procedure being sure that cutout for power cord in rear of 

wrapper seats properly.

6.22 CONDENSER FAN MOTOR

WARNING

DISCONNECT THE POWER CORD FROM THE ELECTRICAL OUTLET.

A. Disconnect fan motor electrical cord from junction box.
B. Remove four (4) screws holding fan guards.
C. Remove four (4) nuts holding fan motor bracket to base of unit and remove from unit.
D. Clean condenser with a brush.
E. Remove fan motor from bracket.
F. Remove fan blade from fan motor.  

Do 

NOT

bend fan blade.

G. To reassemble, reverse above procedure.

14

Содержание CENTURION II 85-0056









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды