lancer CENTURION II 85-0056 Скачать руководство пользователя страница 22

Страница: 22 / 40

7.17 Compressor starts and

A. Faulty ice bank control.

A. Replace ice bank control.

continues to run until

freeze up and will NOT

cut off.

7.18 Warm drinks.

A. Hot incoming water supply

A. Switch to cold water supply.

(from HOT water supply or

heater).

B. No ice bank, defective ice

B. Replace ice bank control.

bank control.

C. Low refrigerant supply.

C. Repair leak and recharge.

D. No ice bank; defective

D. Replace condenser fan motor.

condenser fan motor.

E. No ice bank; compressor

E. Refer to Sections 7.19, 7.20, 7.21,

does not run or runs for a

7.22 and 7.23.

few minutes and stops.

7.19 Compressor does NOT

A. Power supply electrical

A. Reset breaker or replace fuse. If

start (no hum),

breaker tripped or fuse blown.

problem persists:

condenser fan motor

1. Determine reason and correct.

does not run and no

2. Electrical circuit overloaded;

ice bank.

switch to another circuit.

B. Defective ice bank control.

B. Replace ice bank control.

C. Improper or loose wiring.

C. Correct wiring. Refer to wiring

diagram.

D. Low voltage.

D. Measure voltage across common

and run terminal on compressor.

Voltage must not drop below 90%

of rated voltage.

7.20 Compressor does NOT

A. Defective compressor relay

A. Replace compressor relay or

start (no hum), no Ice

or overload.

overload.

bank, but condenser fan B. Defective compressor.

B. Replace compressor.

motor runs.

C. Improper or loose wiring.

C. Correct wiring. Refer to wiring

diagram.

D. Low voltage.

D. Measure voltage across common

and run terminal on compressor.

Voltage must not drop below 90%

of rated voltage.

7.21 Compressor does NOT

A. Improper or loose wiring.

A. Correct wiring. Refer to wiring

start, but hums.

diagram.

B. Low voltage.

B. Measure voltage across common

and run terminal on compressor.

Voltage must not drop below 90%

of rated voltage.

C. Starting relay defective.

C. Replace starting relay. Be sure

to use correct relay. Failure to

use correct relay will cause

compressor failure.

D. Defective compressor.

D. Replace compressor.

7.22 Compressor starts and

A. Low voltage.

A. Measure voltage across common

does switch off of start

and run terminal on compressor.

winding (will only run for

Voltage must not drop below 90%

a few seconds) before

of rated voltage.

internal overload

B. Excessively high refrigerant,

B. This is normal if unit is unplugged

switches compressor

high side pressure.

from electrical outlet then

immediately plugged back into

electrical outlet before refrigerant

pressure has time to equalize.

After about 5 minutes, compressor

will start automatically and run.

(7.22 continued next page)

TROUBLE

CAUSE

REMEDY

Содержание CENTURION II 85-0056









































Результаты поиска

Содержание CENTURION II 85-0056

Отзывы:

Бренды по названию

Популярные бренды

lancer CENTURION II 85-0056, Инструкция по установке и обслуживанию

Результаты поиска

Содержание CENTURION II 85-0056

Отзывы:

Бренды по названию

Популярные бренды