L-Acoustics S Series Скачать руководство пользователя страница 62

Страница: 62 / 80

Corrective maintenance

D/R - HF diaphragm

Tools

• torque screwdriver
• T20 Torx bit
• compressed air blower
• double face adhesive tape

Repair kits

G03316
KR diaphragm 1.75'' Syva

×1

×6

17736

S17736

diaphragm kit for 1.75" driver - 16 Ω

M4×8 Torx

Prerequisite

Trapdoor removed.

See

D/R - Trapdoor

(p.60).

HF loudspeaker disassembled.

See

D/R - HF loudspeaker

(p.61)

Exploded view

For safety reasons, always use the new screws and spare parts provided in the KR.

Make sure the air gap is perfectly clean before reassembly.

Use a blower or double face adhesive to remove any particle.
Position the diaphragm assembly with the positive (red) connector aligned with the red mark.
Gradually tighten the screws following a star pattern.

T20

1.7 N.m

What to do next

Perform the

Acoustical check

(p.40) procedures.

Syva owner's manual (EN) version 1.0

Содержание S Series

















































































Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды

L-Acoustics S Series, Руководство пользователя

Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды