L-Acoustics S Series Скачать руководство пользователя страница 24

Страница: 24 / 80

Mechanical safety

Assessing mechanical safety

Mechanical safety of the rigging system

Before any installation, always model the system in Soundvision and check the

Mechanical Data

section for

any

stress warning

stability warning

In order to assess the actual safety of any array conguration before implementation, refer to the following warnings:

Rated working load limit (WLL) is not enough

The rated WLL is an indication of the element resistance to tensile stress. For complex mechanical systems such as

loudspeaker arrays, WLLs cannot be used per se to determine the maximum number of enclosures within an array

or to assess the safety of a specic array conguration.

Mechanical modeling with Soundvision

The working load applied to each linking point, along with the corresponding safety factor, will depend on

numerous variables linked to the composition of the array (type and number of enclosures, splay angles) and the

implementation of the ying or stacking structure (number and location of ying points, site angle). This cannot be

determined without the complex mechanical modeling and calculation offered by Soundvision.

Assessing the safety with Soundvision

The overall safety factor of a specic mechanical conguration always corresponds to the lowest safety factor

among all the linking points. Always model the system conguration with the Soundvision software and check the

Mechanical Data

section to identify the weakest link and its corresponding working load. By default, a

stress

warning

will appear when the mechanical safety goes beyond the recommended safety level.

Safety of ground-stacked arrays in Soundvision

For ground-stacked arrays, a distinct

stability warning

is implemented in Soundvision. It indicates a tipping hazard

when the array is not secured to the ground, stage or platform. It is the user's responsibility to secure the array

and to ignore the warning.

Additional safety for own arrays

When ying an array, use available holes to implement a secondary safety.

Considerations must be given to unusual conditions

Soundvision calculations are based on usual environmental conditions. A higher safety factor is recommended

with factors such as extreme high or low temperatures, strong wind, prolonged exposition to salt water, etc.

Always consult a rigging specialist to adopt safety practices adapted to such a situation.

Syva owner's manual (EN) version 1.0

Содержание S Series

















































































Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды

L-Acoustics S Series, Руководство пользователя

Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды