L-Acoustics S Series Скачать руководство пользователя страница 30

Страница: 30 / 80

Loudspeaker congurations

Separated

The [SYVA] preset delivers a reference frequency response in medium throw applications.
The [SYVA LOW_100] and [SYVA SUB_100] presets provide Syva Low and Syva Sub with an upper frequency limit at

100 Hz.

[SYVA SUB_100] polarity is reversed to optimize Syva Sub acoustic summation with

Syva/Syva Low.

> 60 cm / 24 in

Enclosures

Syva

Syva Low

Syva Sub

Presets

[SYVA]

[SYVA LOW_100]

[SYVA SUB_100]

Frequency range (-10 dB)

27 Hz - 20 kHz

Grouping subwoofers

Place the subwoofer enclosures side by side. If not possible, the maximum distance between two adjacent

acoustic centers must be 1.7 m if the upper frequency limit of the subwoofer system is at 100 Hz.

Do not forget to add the geometric delays depending on the conguration.

No pre-alignment delay values are required for the Syva system.

Syva owner's manual (EN) version 1.0

Содержание S Series

















































































Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды

L-Acoustics S Series, Руководство пользователя

Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды