L-Acoustics S Series Скачать руководство пользователя страница 53

Страница: 53 / 80

Connection to LA amplied controllers

Connection to LA amplied controllers

Enclosure drive capacity per amplied controller

Make sure the total number of connected enclosures does not exceed the maximum number of enclosure per controller

(refer to the footnote).

LA2Xi

LA4X

LA7.16i

LA12X

per output

total per output

total

Syva

1/4 (SE), 1/2 (BTL)

1/4

1/10

3 / 12

Syva Low

1/4 (SE)

1 / 4

1 / 8

2 / 6

Syva Sub

1/4 (SE), 1/2 (BTL)

1 / 4

1 / 16

3 / 12

For Syva / Syva Low / Syva Sub (LA2Xi/LA7.16i)

Refer to the cabling schemes to connect the enclosures to different types of output connectors.

Refer to the

LA2Xi owner's manual

for more information on output congurations.

Terminal block output (LA2Xi SE / LA7.16i)

1−

2.5 mm² cables

Terminal block output (LA2Xi BTL)

2−

2.5 mm² cables

For Syva / Syva Low / Syva Sub (LA4X, LA12X)

Refer to the cabling schemes to connect the enclosures to different types of output connectors.

One-channel speakON output

1+/1-

LA12X can drive up to two Syva Low per output, but no more than six per controller at high level.

For passive loudspeakers, the value corresponds to the number of enclosures in parallel on the output. For active

loudspeakers, the value corresponds to the number of sections in parallel on the output.

Syva owner's manual (EN) version 1.0

Содержание S Series

















































































Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды

L-Acoustics S Series, Руководство пользователя

Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды