L-Acoustics S Series Скачать руководство пользователя страница 14

Страница: 14 / 80

Electro-acoustical description

Connectors

Syva

Syva offers multiple types of connectors. Use

one

type of connector at a time.

Use the

speakON connector

to connect the enclosure with an SP cable.

The speakON connector is only accessible if Syva Wall is used with a wedge.
Refer to

Wall-mounting Syva

(p.44).

Use the

screw terminal

to connect the enclosure with speaker wire.

Put the gasket and cover back on the connector once the wire is installed.

IN +

IN -

When the screw terminal is not in use, put the gasket and cover back on to avoid leaks.

Internal pinout for L-Acoustics 2-way passive enclosures

screw terminal points

IN +

IN -

speakON points

1 +

1 -

2 +

2 -

transducer connectors

Not linked

Syva owner's manual (EN) version 1.0

Содержание S Series

















































































Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды

L-Acoustics S Series, Руководство пользователя

Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды