L-Acoustics S Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 80

background image

Inspection and preventive maintenance

Listening test

enclosure

preset

usable bandwidth

Syva

[SYVA]

87 Hz - 20 kHz

Syva Low

[SYVA LOW_100]

from 40 Hz

Syva Sub

[SYVA SUB_100]

from 27 Hz

Procedure

1.

Load the preset on an LA2Xi / LA4X / LA7.16i / LA12X amplied controller.

2.

Connect a sinus generator to the amplied controller.

Risk of hearing damage

Set a low sound level to start and use ear protection to adjust before testing.

3.

Scan the bandwidth focusing on the usable range.

The sound should remain pure and free of unwanted noise.

Troubleshooting for LF/MF speakers

One or more LF/MF speaker produces distorted, buzzing, rubbing, clicking, mufed or weak sound.

Possible causes

• The screws are not tightened with the appropriate torque.
• There is an air leak in the gasket.
• There is dust on the cone.
• The cone is damaged.
• The surround is torn or delaminated.
• The voice coil or the spider is damaged.

Procedure

1.

Perform the speaker disassembly procedure.

2.

Visually inspect the cables and the connectors.

3.

Visually inspect the speaker cone, the voice coil and the spider.
If any damage is visible, replace the speaker.

4.

Carefully clean the speaker with a dry cloth.

5.

Perform the reassembly procedure.
Replace the speaker gasket and the screws.
Apply the recommended torque.

6.

Repeat the listening test.
If the problem persists, replace the speaker.

Troubleshooting for HF drivers

One or more HF driver produces high-frequency harmonic distortions, strange vibrations or weak sound.

Possible causes

• There are foreign particles on the air gap.
• The diaphragm is not centered correctly.
• The screws used for reassembly are too loose.
• The diaphragm is damaged.

Procedure

1.

Perform the diaphragm disassembly procedure.

2.

Visually inspect the diaphragm and the voice coil.
If any damage is visible, replace the diaphragm.

42

Syva owner's manual (EN) version 1.0

«
...
40
41
42
43
44
...
»

Содержание S Series

















































































Отзывы:

Нет отзывов

Похожие инструкции для S Series

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 34

Бренд: Harman Kardon Страницы: 2

Бренд: Metrix Страницы: 4

Expedition XP300

Бренд: Samson Страницы: 72

Biamplified Direct Field Monitor System

Бренд: Event electronics Страницы: 8

Бренд: Kicker Страницы: 2

Бренд: GOgroove Страницы: 5

Бренд: JBL Страницы: 65

Бренд: EAW Страницы: 5

Бренд: Karma Страницы: 12

Spacia CI-MM3-II

Бренд: Phase Technology Страницы: 4

Бренд: ADS Страницы: 8

Бренд: LyxPro Страницы: 3

Бренд: Sharper Image Страницы: 2

Бренд: iLive Страницы: 12

Бренд: Karma Страницы: 8

AL-SND05X-001/MUSEO

Бренд: Altec Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды