L-Acoustics S Series Скачать руководство пользователя страница 61

Страница: 61 / 80

Corrective maintenance

D/R - HF loudspeaker

Tools

• torque screwdriver
• 4 mm hex bit - spherical head
• 10 mm screwdriver extension

Repair kits

G03315
KR compression driver 1.75'' Syva

×1

×2

G100087

S342

1" HF speaker assembly - 16 ohms

M5×20 hex

Prerequisite

Trapdoor removed.

See

D/R - Trapdoor

(p.60).

Exploded view

For safety reasons, always use the new screws and spare parts provided in the KR.
If no new screws are available, use blue threadlocker.

Use a spherical head bit to access the screws of the lateral speakers.

If necessary, unplug the cables to remove the speakers. Refer to

Connecting cables to the lter (HF area)

(p.63).

Position the positive (red) connector toward the lter.

3 N.m

4 mm

For each speaker, make sure the driver exit and the waveguide mouth t together.
The speaker plate must be level with the cabinet.

What to do next

Perform the

Acoustical check

(p.40) procedures.

Syva owner's manual (EN) version 1.0

Содержание S Series

















































































Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды

L-Acoustics S Series, Руководство пользователя

Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды