L-Acoustics KARA Скачать руководство пользователя

Страница: 78 / 201

Rigging procedures

10.

Detach SB18#3 from SB18#2 as follows:

a) Disconnect a T-BLP from the bottom of SB18#2.
b) Rotate the rigging arm down.

c) Re-connect the T-BLP to SB18#3 so as to lock the rigging arm in closed position.

d) Repeat this procedure until all 4 arms are locked in closed position.

11.

Raise the array so that SB18#2 is separated from SB18#3.

12.

Attach two dolly boards to SB18#3 and 4.

13.

Detach SB18#4 from SB18#3 by applying step

(p.78).

14.

Remove SB18#3 and 4 from the rigging location.

15.

Repeat steps

(p.77) to 14 to separate the SB18s from the array just until SB18#1 and 2 are remaining attached

to the M-BUMP.

16.

Lower the array until it rests on the ground.

17.

Remove the motor hook(s) or stinger(s) from the shackle(s) of the M-BUMP.

Kara owner's manual (EN) version 1.0

Содержание KARA










































































































































































































Результаты поиска

Содержание KARA

Отзывы:

Похожие инструкции для KARA

Бренды по названию

Популярные бренды

L-Acoustics KARA, Руководство пользователя

Результаты поиска

Содержание KARA

Отзывы:

Похожие инструкции для KARA

Бренды по названию

Популярные бренды