L-Acoustics KARA Скачать руководство пользователя | Manualshive

Страница: 103 / 201

background image

Rigging procedures

Procedure

1.

Assemble a KARA-MINIBU/KARA-MINIBUEX stacking platform as follows:

a) Turn the KARA-MINIBU so that the text of the identication plate is upside down.
b) Position a rst KARA-MINIBUEX on the laser plate side of the KARA-MINIBU by turning the KARAMINIBUEX feet

pointing down and inserting the stud into the slit of the KARA-MINIBU located near the laser plate.

c) Drive 3 bolts to the 3 holes shown in the gure below (6 mm hex bit, 13 mm hex key, 7 N.m/63 in.lb f ).

d) Repeat the procedure with a second KARA-MINIBUEX on the other side of the KARA-MINIBU.

2.

If KARA-ANGARMEX are intended to be used (see

Array site angle setting

(p.198)), attach two KARA-ANGARMEX

to the platform as follows:

a) Remove an R-BLP from a rear corner of the KARA-MINIBU.

When using KARA-ANGARMEX the platform must be put in front extension conguration (see

platform conguration

(p.197)).

b) Insert the single part of a rst KARA-ANGARMEX into the corner slit: position it vertically with sling ring towards

the front and indentation resting on the spacer.

c) Align the KARA-ANGARMEX and KARA-MINIBU holes and secure them together by re-inserting the R-BLP.

d) Repeat the procedure with a second KARA-ANGARMEX on the other rear corner of the KARA-MINIBU.

3.

Remove both front R-BLP from the KARA-MINIBU.

The front and rear sides are dened according to the chosen conguration.

4.

If KARA-ANGARMEX are attached to the KARA-MINIBU, remove both T-BLP from them. Otherwise, remove both rear

R-BLP from the KARA-MINIBU.

5.

Bring a full Kara ight-case to the stacking location and remove the lid. In the following, the enclosures will be

designated as KARA#1 to KARA#3 from top to bottom.

Kara owner's manual (EN) version 1.0

103

«
...
101
102
103
104
105
...
»

Содержание KARA










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KARA

Бренд: Cambridge SoundWorks Страницы: 12

Бренд: OFT Страницы: 9

Бренд: Tannoy Страницы: 2

Бренд: Dali Страницы: 8

Бренд: Dali Страницы: 42

Бренд: Dali Страницы: 34

Бренд: Dali Страницы: 2

Бренд: Dali Страницы: 37

Бренд: Dali Страницы: 2

Бренд: Dali Страницы: 15

Бренд: TAC Страницы: 20

Бренд: Falcon Страницы: 4

Бренд: JBL Страницы: 6

Бренд: 808 Страницы: 10

Бренд: GPX Страницы: 16

Бренд: YeriSystems Страницы: 7

Бренд: Commell Страницы: 13

Бренд: eMoMo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды