L-Acoustics KARA Скачать руководство пользователя | Manualshive

Страница: 102 / 201

background image

Rigging procedures

Using KARA-MINIBU

Modeling and safety

A Kara array must be stacked onto a KARA-MINIBU/KARA-MINIBUEX platform (platform stacked array).
Any platform stacked array must be modeled before installation so as to ensure acoustical conformity. This can be done

using L-Acoustics

Soundvision Software

which will assist the user to:

• Determine the number of required Kara enclosures.
• Calculate the inter-enclosure angles.

A platform stacked array requires to be installed on a perfectly horizontal and regular surface. It can be

composed of a maximum of 6 KARA enclosures along with all loudspeaker cables (refer to

Mechanical safety

(p.26)) within the following setup safety limits:

• If the Kara array is at (all inter-enclosure angles are close to 0°), the platform must be installed in front extension

conguration (refer to

Stacking platform conguration

(p.197)) and the site angle of the bottom Kara must be set

within the range given in the table below (refer to

Array site angle setting

(p.198) for angle settings):

Platform stacked Kara array safe congurations

Number of Kara

Bottom Kara authorized angle range

1 - 3

From -15° to +5°

4

From -11° to +5°

5 - 6

From -7.5° to +5°

• If the Kara array is strongly curved (all inter-enclosure angles are close to 10°), the platform must be installed in rear

extension conguration (refer to

Stacking platform conguration

(p.197)).

The Kara, KARA-MINIBU, and KARA-MINIBUEX fully integrated rigging systems allow assembling the array with no need

for any external accessory. The following rst procedure describes how to assemble a vertical Kara platform stacked

array. The second procedure describes how to disassemble the array.

Array mounting

About this task

All along the procedure:
Strictly follow the sequence of the successive steps.
Systematically verify that each BLP is fully inserted.
Systematically verify that each bolt is fully driven on the KARA-MINIBUEX.
For clarity purposes the loudspeaker cabling procedure will not be described.
The loudspeaker cables will not be represented on the gures.

Required tools

• electric screwdriver with torque selector
• 6 mm hex bit6 mm hex bit
• 13 mm hex key

102

Kara owner's manual (EN) version 1.0

«
...
100
101
102
103
104
...
»

Содержание KARA










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KARA

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 22

Бренд: Panasonic Страницы: 44

Sound Slayer SC-HTB01

Бренд: Panasonic Страницы: 12

Sound Slayer SC-HTB01

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 4

Бренд: JBL Страницы: 3

Бренд: Panasonic Страницы: 122

SAPM71 - MINI HES W/CD PLAYER

Бренд: Panasonic Страницы: 12

Бренд: iDance Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды