L-Acoustics KARA Скачать руководство пользователя

Страница: 61 / 201

Rigging procedures

Open the four KARA#1 arms as follows (repeat on both sides of the enclosure):

a) Remove the front top R-BLP from its

storage

hole, rotate the front arm up, slide it down, and lock it in place by

re-inserting the R-BLP into its

link

hole.

The front top

storage

and

link

holes are the same.

b) Remove the rear top R-BLP from its

storage

hole, slide the angle arm so as to align the cursor with angle label

5°, and lock it in place by re-inserting the R-BLP into angle hole 1°/3°/5°/7.5°/10°.

It is recommended to select the 5° angle on the Kara intended to be attached to the KARA-MINIBU; in that

way the KARA#1 axis will be parallel to the KARA-MINIBU.

Attach a KARA-MINIBU to KARA#1 as follows:

a) Remove the four R-BLP from the KARA-MINIBU.
b) Turn the KARA-MINIBU so that the text of the identication plate is readable and the laser plate is placed at the

front (towards audience).

c) While keeping this orientation, align the four link points of KARA-MINIBU with the four arms of KARA#1 and

secure each pair together by re-inserting the four R-BLP into the same holes (insert both rear R-BLP rst).

Kara owner's manual (EN) version 1.0

Содержание KARA










































































































































































































Результаты поиска

Содержание KARA

Отзывы:

Похожие инструкции для KARA

Бренды по названию

Популярные бренды

L-Acoustics KARA, Руководство пользователя

Результаты поиска

Содержание KARA

Отзывы:

Похожие инструкции для KARA

Бренды по названию

Популярные бренды