L-Acoustics KARA Скачать руководство пользователя

Страница: 31 / 201

Loudspeaker congurations

Kara line source with separated SB18, KS21, SB28, or KS28

3 Kara : 2 SB18 or KS21 / 2 Kara : 1 SB28 or KS28

Enclosure

Kara

SB18, KS21, SB28 or KS28

Preset

[KARA]

[xxxx_60]

Frequency range (-10 dB)

32 Hz - 20 kHz with SB18
29 Hz - 20 kHz with KS21
25 Hz - 20 kHz with SB28 or KS28

Use [xxxx_xx_C] or [xxxx_xx_Cx] on a reversed subwoofer in a cardioid conguration

The cardioid conguration consists in reversing 1 element in an array of 4 subwoofers.
Refer to the subwoofer owner's manual and to the

Cardioid congurations

technical bulletin.

Grouping subwoofers

Place the subwoofer enclosures side by side. If not possible, the maximum distance between two adjacent

acoustic centers must be 2.8 m or 1.7 m if the upper frequency limit of the subwoofer system is at 60 Hz or

100 Hz, respectively.

Delay values

Do not forget to add the pre-alignment and geometric delays depending on the conguration.

Pre-alignment delays

presets

pre-alignment delay values and polarity settings

[KARA] + [SB18_60]

Kara = 2.5 ms

SB18 = 0 ms

[KARA] + [SB18_60_C]

Kara = 8 ms

SB18 = 0 ms

[KARA] + [SB18_60_Cx]

Kara = 6.5 ms

SB18 = 0 ms

Kara owner's manual (EN) version 1.0

Содержание KARA










































































































































































































Результаты поиска

Содержание KARA

Отзывы:

Похожие инструкции для KARA

Бренды по названию

Популярные бренды

L-Acoustics KARA, Руководство пользователя

Результаты поиска

Содержание KARA

Отзывы:

Похожие инструкции для KARA

Бренды по названию

Популярные бренды