KYOWA DPM-900 Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 64

background image

1

STANDARD ACCESSORIES

The DPM-900/950 series Dynamic Strain Amplifier (hereinafter referred to as the DPM-900/950 series)
comes with the following accessories. After unpacking, check to be sure that they are included.

Instruction Manual

1

Simplified instruction manual seal

1

AC power cable (P-25)

1

3p - 2p conversion plug (CM-52)

1

BNC cable (U-59 and U-08)

1 each

Fuses, midget type (1.0 A and 0.5 A)

1 each

Product Warranty

1

SAFETY PRECAUTIONS

The DPM-900/950 series is designed in accordance with “8. SPECIFICATIONS.” Do not use the
DPM-900/950 series in an environment exceeding the specifications. Or, failure of the DPM-900/950
series may result.

PRIOR TO USE

For safe use of the DPM-900/950 series, do not forget to read the “Safety Precautions” prior to use.
Kyowa Electronic Instruments Co., Ltd. assumes no liability for any damages resulting from user’s failure
to comply with the safety precautions.
For safety operation of the DPM-900/950 series, the following symbol mark is used.

Indicates “PROTECTIVE GROUND TERMINAL.”
Be sure to connect the GND terminal to the ground.
However, excludes when grounding with a 3-prong AC power cable.

SAFETY SYMBOLS

For safety operation of the DPM-900/950 series, the following symbol marks are used in the Instruction
Manual.

WARNING

Improper operation of the system may result in death or severe injury of the
operator.

CAUTION

Improper operation of the system may result in injury of the operator and
physical damage of the system.

«
...
4
5
6
7
8
...
»

Содержание DPM-900 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для DPM-900 Series

Бренд: NAD Страницы: 2

Бренд: DaytonAudio Страницы: 6

Бренд: Offel Страницы: 2

Бренд: DaytonAudio Страницы: 4

Бренд: One for All Страницы: 26

Sona Flex SF-16B

Бренд: Audio Authority Страницы: 8

Phat Tuesday MGA11000H

Бренд: Bazooka Страницы: 60

Princeton Reverb

Бренд: Fender Страницы: 32

Бренд: Ericsson Страницы: 34

Бренд: Art Страницы: 25

Бренд: Altimium Страницы: 36

Бренд: audiophony Страницы: 5

Бренд: Forney Страницы: 18

Бренд: Line Magnetic Страницы: 13

Бренд: Bugera Страницы: 3

Zero Five The Falcon

Бренд: B2 Audio Страницы: 14

Бренд: QUAD Страницы: 14

Бренд: Link electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды