KYOWA DPM-900 Series Скачать руководство пользователя страница 20

Страница: 20 / 64

4-4 SELECTING MODE

The DPM-900/950 series provides “Normal Mode”, “TEDS Mode” “ACTL LOAD Mode” and “TPN/DLT

Measuring Mode.” Setting methods of the internal gain and display unit of the indication varies with every

mode.

“TEDS Mode”

Setting and cancelation is possible by pressing and holding TEDS switch.

While “TEDS Mode” is set, TEDS switch light up.

“ACTL LOAD Mode”

Setting and cancelation is possible by pressing and holding ACTL LOAD

switch.

While “ACTL LOAD Mode” is set, ACTL LOAD switch light up.

“Normal Mode”

When both TEDS switch and ACTL LOAD switch is off, “Normal Mode”

is set.

“TPN/DLT Measuring Mode”

Turning on “Setting Switch 4” on the rear panel make it setting.

(DPM-911/951 only)

However, “Normal Mode” and “TPN/DLT Measuring Mode” have no outward difference. For how to

confirm modes, read the MEMO in “5-15 TPN/DLT MEASURING MODE.”

For the setting methods of the internal gain, read “5-7 INTERNAL GAIN.”

4-5 BASIC BALANCING

4-6 SETTING MEASURING PARAMETERS

This section describes how to set the measuring parameters of the DPM-900/950 series.

4-6-1 Setting an Basic Internal Gain

The DPM-900/950 series performs balancing completely

electronically.

Make sure that input signals are connected, and then press the

BAL switch twice.

Balancing will then be carried out irrespective of the setting

conditions of other parameters.

It is necessary to set an internal gain (sensitivity

*10

)

properly to assure the correct strain measuring.

This section describes how to select the internal gain with

the CAL switch.

For details, read “5-7 INTERNAL GAIN.”

First, estimate the strain to be measured.

When using the strain gage transducer for the input, set

the internal gain from the rated output.

For example, when using the strain gage transducer with

±1000 m/m rated output.

For setting the internal gain with 10 V of the rated input,

set VOLTAGE OUT switch to 10.00 and CAL switch to

1000 and press the SET switch twice.

After the internal gain is correctly set, (SET)

appears on the monitor.

VOLTAGE OUT switch

CAL switch

SET switch

BAL switch

After balancing is executed, the panel meter will not necessarily read exactly 0 but several mV

remains.

Carry out fine balancing by using the V ADJ. switch if necessary.

MEMO

Содержание DPM-900 Series

































































Результаты поиска

Содержание DPM-900 Series

Отзывы:

Похожие инструкции для DPM-900 Series

Бренды по названию

Популярные бренды

KYOWA DPM-900 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DPM-900 Series

Отзывы:

Похожие инструкции для DPM-900 Series

Бренды по названию

Популярные бренды