KYOWA DPM-900 Series Скачать руководство пользователя страница 56

Страница: 56 / 64

9-4 TROUBLE SHOOTING

The DPM-900/950 series provides several error indications.

The error indication, status at that time, and remedies are described in the following table. If any error

indication appears on the monitor, check the following table for remedies.

Error

Displayed Timing

Status

Remedy

After doing bridge
check
or
After the setting the
internal gain
(ACTL LOAD mode)

1) The sensor is not connected.

1) Connect the sensor.

2) The bridge box is not

connected or the strain gage
(s) is not connected to the
bridge box.

2) Connect the bridge box or strain

gage.

3) Cable is broken.

3) Repair or replace the cable.

4) Input strain exceeds ±10000

µm/m.

4) Make input strain within ±10000

µm/m.

After doing bridge
check

Not applicable sensor is
connected.

Connect the applicable sensor.

After turning ON the
power, when the
input from the
external OSC is not
coming (slave only)

OSC frequency or voltage is
faulty.

Replace the normal master.

After setting the
internal gain
(normal mode)

Less than minimum internal
gain (×200) is set.

Decrease the setting value of the

CAL switch or increase the setting

value of the VOLTAGE OUT
switch and set the internal gain
again.

After setting the
internal gain
(normal mode)

Higher than maximum internal
gain (×20000) is set.

Increase the setting value of the

CAL switch or decrease the setting

value of the VOLTAGE OUT
switch and set the internal gain
again.

After setting the
internal gain
(TEDS mode)

1) TEDS-installed sensor is not

connected.

1) Connect the TEDS-installed

sensor.

2) TEDS information cannot be

read. (Cable is broken or the
sensor is faulty.)

2) Repair the cable or replace the

sensor.

After setting the
internal gain
(TEDS mode)

The applied voltage is outside
the range of the sensor's
recommended excitation
voltage.

From the rear setting switch, set the
bridge voltage to the appropriate
value and reboot.
Or replace the sensor that the
sensor’s recommended excitation
voltage matches the current bridge
voltage.

After setting the
internal gain
(TEDS mode)

Less than Minimum internal
gain (×200) is set.

Increase the setting value of the

VOLTAGE OUT switch and set the

internal gain again.

After setting the
internal gain
(TEDS mode)

1) Higher than maximum internal

gain (×20000) is set.

2) Setting value of VOLTAGE

OUT switch exceeds 10.00 V

1) Decrease the setting value of the

VOLTAGE OUT switch and set

the internal gain again.

2) Setting value of VOLTAGE OUT

switch set 10.00V or less.

After setting the
internal gain
(ACTL LOAD mode)

1) Less than minimum internal

gain (×200) is set.

2) Input strain is too large.
3) Input strain is minus.

1) Increase the setting value of the

VOLTAGE OUT switch and set

the internal gain again.

2) Reduce the input strain.
3) Set the input strain to plus.

After setting the
internal gain
(ACTL LOAD mode)

Higher than maximum internal
gain (×20000) is set.

Decrease the setting value of the

VOLTAGE OUT switch and set the

internal gain again.

Contact KYOWA or our representatives even if the error indication appears after conducting the remedies.

Содержание DPM-900 Series

































































Результаты поиска

Содержание DPM-900 Series

Отзывы:

Похожие инструкции для DPM-900 Series

Бренды по названию

Популярные бренды

KYOWA DPM-900 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DPM-900 Series

Отзывы:

Похожие инструкции для DPM-900 Series

Бренды по названию

Популярные бренды