KYOWA DPM-900 Series Скачать руководство пользователя страница 13

Страница: 13 / 64

２１

12) POWER switch

POWER ON/OFF

Press the POWER switch for turned ON and press again for turned OFF.

13) INT lamp

Lights up when using the internal oscillator output for the excitation

voltage of the DPM-900/950 series as the carrier.

14) Bar graph meter

Indicates an output voltage by the length of the bar.

One LED segment corresponds to 2 V.

When the internal gain is fine adjusted to lower than ×200, 0 (orange LED)

flickers. For details, read “4-6-5 Sensitivity Fine Adjustment.”

15) L.P.F. lamp

Displays the cutoff frequency of the L.P.F.

16) Monitor

Indicates the output voltage of the OUTPUT A and B in general.

If the output voltage at the OUTPUT A or OUTPUT B exceeds

11V,

numbers or characters on the monitor flicker.

In addition, indicates the physical quantity in TEDS mode and error content

in error mode.

17) BV 0.5 V lamp

When outputting 0.5 Vrms excitation voltage, the BV 0.5 V lamp lights up

and when outputting 2 Vrms excitation voltage, the BV 0.5 V lamp lights

out.

18) V lamp

Lights up when displaying voltage on the monitor. Lights out only in the

TEDS mode.

19) H.P.F. lamp

Lights up when the H.P.F. switch is set to valid. When invalid, the H.P.F.

lights out.

20) VOLTAGE OUT lamp

Lights up after setting the internal gain correctly.

After setting the internal gain, if the set value of the VOLTAGE OUT

switch is changed, the VOLTAGE OUT lamp flickers.

21) CAL lamp

Lights up after setting the internal gain correctly.

After setting the internal gain, if the set value of the CAL switch is

changed, the CAL lamp flickers.

Lights out when in TEDS mode and ACTL LOAD mode.

Internal gain: Gain from the input to the output of the DPM-900/950 series.
Capable of setting the internal gain within ×200 to ×20000.
In addition, when the internal gain is large, it means high sensitivity and when it is small, low
sensitivity.

NOTE

１２

１３

１４

１５

１６

１７

１８

１９

２０

Содержание DPM-900 Series

































































Результаты поиска

Содержание DPM-900 Series

Отзывы:

Похожие инструкции для DPM-900 Series

Бренды по названию

Популярные бренды

KYOWA DPM-900 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DPM-900 Series

Отзывы:

Похожие инструкции для DPM-900 Series

Бренды по названию

Популярные бренды