KYMCO AK 550 Скачать руководство пользователя страница 68

Страница: 68 / 461

2.Periodic Maintenance

AK 550

2-37

Change Pressure Unit

Turn KEYLESS Main Switch ON, the Model Symbol will light up. Push the

Dashboard and noodoe Switch to “m” position and press the UP button to change

over to TPMS Mode. Pressing “O” button on the Right Handlebar Switch to

change units in the sequence of [kgf/cm

→ bar → psi → kpa].

■Anomaly:

1. With Main Switch set to ON, when Tire Pressure Indicator in the Dashboard

lights up continuously, it may be due to a pressure > 3.2 kgf/cm

or < 1.6

kgf/cm

of Front Tire; or a pressure >3.75 kgf/cm

or < 1.65 kgf/cm

(23.4psi)

of Rear Tire. Change over to TPMS Mode by pressing the Mode button, the

tire pressure value will be flashing.

2. Tire Pressure Indicator will light up continuously if controller is faulty. Change

over to TPMS Mode by pressing the Mode button, the

symbol will appear.

3. Tire Pressure Indicator will light up continuously if signal of tire pressure

sensor fails to reach the controller due to environmental interference. Change

over to TPMS Mode by pressing the Mode button, - - - will appear.

4. When power of battery in Tire Pressure Sensor is low, Tire Pressure Indicator

will light up constantly. The owner shall prepare for replacing with a new

wireless Tire Pressure Sensor.

5. Tire Pressure Indicator flashes quickly if tire pressure drops fast; it flashes

slowly if tire pressure drops slowly.

Содержание AK 550














































































































































































































































































































































































































































































Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды

KYMCO AK 550, Руководство по обслуживанию

Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды