KYMCO AK 550 Скачать руководство пользователя страница 346

Страница: 346 / 461

10..Brake System

AK 550

Front Wheel Disassembly

Remove the collars from each side of the wheel. Inspect the bearing seals and

the O-rings seals on the collars. Replace the seals if they are in poor condition.

Inspect the wheels and axle.

Inspect the wheel bearings by turning them in the hub. If the bearings have play

in them or are rough replace all the bearings for that wheel.

When installation: Make sure the tire direction of rotation marker is correct. Slide

the front wheel into the fork. Fit the brake disc between the brake pads in the

front caliper.

Set the front wheel on the ground. Pump the front suspension up and down

several times to seat the front axle. Pump the front brake lever to establish

pressure and to seat the pads against the disc. If the Brakes do not pump up

correctly check the brake fluid.

10-15

Содержание AK 550














































































































































































































































































































































































































































































Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды

KYMCO AK 550, Руководство по обслуживанию

Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды