KYMCO AK 550 Скачать руководство пользователя страница 315

Страница: 315 / 461

9.Electrical Systems

AK 550

9-50

Grip Heater

After turning ON the Main Switch, press and hold Handlebar Heater Button for 3

seconds or more to activate/deactivate Handlebar Heating Function.

After activating Handlebar Heater controller, click the Heater button to select

heating level in the sequence of 1 > 2 > 3 > 1 > 2 ...

Handlebar Heater State Indicator:

1. After turning ON KEYLESS Main Switch, a self-check is performed with the

LED indicator flashing in a 1-white and 1-red format.

2. After KEYLESS Main Switch ON and indicator self-check, in the event of a

Handlebar Heater anomaly, the indicator will flash in red, with the Handlebar

Heater function disabled. (Refer to anomaly states below for indicator flashing

modes.)

3. After KEYLESS Main Switch ON, press and hold the button to activate

Handlebar Heater. Indicator lights in white constantly for normal operation.

4. Turn KEYLESS Main Switch OFF or press and hold the button to deactivate

Handlebar Heater. The indicator will go out, indicating the function is switched off.

5. If Handlebar Heater is faulty, the indicator will flash in red.

When Handlebar Heater function is OFF, anomaly states are as follows:

a. 1 flashes (on/off) per 0.2s followed by 2s off: Handlebar Heater function is

faulty.

b. 2 flashes (on/off) per 0.2s followed by 2s off: Handlebar Heater temperature

sensor is faulty.

c. 1 flash (on/off) per 0.3s followed by 0.3s off: Handlebar/ Controller Circuit is

faulty.

After eliminating the fault and re-starting (Key Off → Key On) the vehicle,

indicator will resume normal operation.

Clicking the button when the indicator is flashing in red will stop the flashing. For

the sake of your safety, please go to a KYMCO dealer for check-up.

Содержание AK 550














































































































































































































































































































































































































































































Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды

KYMCO AK 550, Руководство по обслуживанию

Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды