KYMCO AK 550 Скачать руководство пользователя страница 197

Страница: 197 / 461

6.Fuel System

AK 550

6-10

Spark Plug

Turn the ignition switch to ON, lift the side stand, hold in one of the brake levers,

and push the engine start button. The plug should spark.

Caution: Do not touch the spark plug or spark plug wire while cranking or running

the engine as this can result in a severe shock.

Remove the spark plug with a spark plug with a 5/8 in socket.

Spark plug

NGKCR7E

Check the spark plug to see if it is the correct type and gapped properly. If the

spark plug is black and fouled, replace it.

If the spark plug center electrode or side electrode are corroded or damaged,

or if the insulator is cracked, replace the plug.

Содержание AK 550














































































































































































































































































































































































































































































Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды

KYMCO AK 550, Руководство по обслуживанию

Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды