KYMCO AK 550 Скачать руководство пользователя страница 60

Страница: 60 / 461

2.Periodic Maintenance

AK 550

2-29

Throttle Free Play

Inspection

Check the throttle cable free play by gently rotating the throttle grip back until

resistance is felt.

Throttle grip free play

2 ~ 6 mm

Make sure the throttle moves smoothly and returns on its own. Start the engine

and let it warm up. Turn the handlebars from side to side, if the engine rpm

changes either the free play is too small or the throttle cables are not routed

properly. Check and correct the cause.

Adjustments of the throttle free play can be made with the cable adjusters below

the grip throttle.

Loosen the throttle cable adjuster lock nut and turn the adjuster to achieve the

specified free play.

When the free play has been moved into specification hold the adjuster in place

and tighten the locknut securely.

Resistance First Felt

Closed

Adjuster lock nut

Adjuster

Содержание AK 550














































































































































































































































































































































































































































































Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды

KYMCO AK 550, Руководство по обслуживанию

Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды