KYMCO AK 550 Скачать руководство пользователя страница 184

Страница: 184 / 461

5. Cooling System

AK 550

Inspection

Water Temperature Sensor

Inspect the WTS in a similar manner as the thermosensor. Measure the

resistance between the WTS terminals and compare this to the specifications.

Water temperature

sensor resistance

At 60°C

703.8±40.9 Ω

At 90°C

260.7±15.1 Ω

At 120°C

111.1±7.8 Ω

Thermostat

The thermostat should be closed at room temperature.

Suspend the thermostat and a thermometer in a pot of water with string. Make

sure the thermostat and the thermometer are not touching the pot. Bring the

temperature up to the specification slowly and check the operation of the

thermostat.

The valve should begin to open around 82° C. The valve should lift 3.5 - 8 mm

at 95° C.

After the thermostat has been open for around 5 min. allow the thermostat to cool.

The thermostat should close at 81° C.

Replace the thermostat with a new unit if it fails to function properly.

5-16

Содержание AK 550














































































































































































































































































































































































































































































Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды

KYMCO AK 550, Руководство по обслуживанию

Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды