KYMCO AK 550 Скачать руководство пользователя страница 267

Страница: 267 / 461

9.Electrical Systems

AK 550

9-2

• When a battery is overcharged, some symptoms can be found. If there is a

short circuit inside the battery, no voltage is produced on the battery terminals. If

the rectifier won‘t operate, the voltage will become too high and shorten the

battery service life.

• If a battery is not used for a long time, it will discharge by itself and should be

recharged every 3 months.

• A new battery filled with electrolyte will generate voltage within a certain time

and it should be recharged when the capacity is insufficient. Recharging a new

battery will prolong its service life.

• Inspect the charging system according to the sequence specified in the

Troubleshooting.

• Do not disconnect and soon reconnect the power of any electrical equipment

because the electronic parts in the regulator/rectifier will be damaged. Turn off

the ignition switch before operation.

• It is not necessary to check the MF battery electrolyte or fill with distilled water.

• Check the load of the whole charging system.

• Do not quick charge the battery. Quick charging should only be done in an

emergency.

• Remove the battery from the motorcycle for charging.

• When replacing the battery, do not use a traditional battery.

• When charging, check the voltage with an electric tester.

Содержание AK 550














































































































































































































































































































































































































































































Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды

KYMCO AK 550, Руководство по обслуживанию

Результаты поиска

Содержание AK 550

Отзывы:

Похожие инструкции для AK 550

Бренды по названию

Популярные бренды