KWB Easyfire страница 133 Скачать руководство пользователя | Manualshive

Страница: 133 / 220

background image

Page

134

IM Easyfire 10/2008

© KWB – Kraft und Wärme aus Biomasse GmbH

15 Suction conveyor, lance + fabric tank

15 Suction conveyor, lance + fabric tank

15.2

Installation, removal pot with lance

1.) Flange

ring

Dismount the flange ring from the removal pot.
Fit the flange ring over the sown-on “collar” of the fabric tank.

Flange ring

2.) Removal

pot

Insert the screws through the flange ring from ABOVE!
This prevents damage to the tank fabric.

Bolt the flange ring, collar, and extractor pot together.

Removal pot

3.) Earth connection for the hoses

To ensure that static discharges do not occur when transporting the
bulk material, the entire transport hose and fuel extractor system
must be connected in a manner that is electrically conductive and
it must they grounded via the equipotential busbar!

Strip the earth strand 5 cm.
Bend the earthing strand into the hose.

Earthing wire

2

2

1

1

4.) Connecting the hoses
Slide 2 hose clamps over the nozzles.
Slide the hose clamp completely over the inside connector.
Connect the return flow hose 1 on the upper connecting piece.
(Hose from the turbine)
Connect the pellet hose 2 on the upper connecting piece.
(Hose to the suction tank cover)

Tighten the hose clamps – the connection must be sealed and secured
so that it cannot be pulled off.

Connect hoses

15.3

Lay out transport hose

see point 13.3

15.4 Fabric

tank

see section 9

15.5 Final

inspection

Ensure that ALL components and connections are correctly installed!

To conclude, ensure that the conveyor system is free of foreign objects!

MA-Easyfire 10.2008_EN.indd 134

MA-Easyfire 10.2008_EN.indd 134

30.03.2009 13:31:29 Uhr

30.03.2009 13:31:29 Uhr

«
...
131
132
133
134
135
...
»

Содержание Easyfire





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Easyfire

ecoMAX pro 18 E

Бренд: Vaillant Страницы: 36

Vitodens 200-W B2HA-45

Бренд: Viessmann Страницы: 184

Бренд: Ideal Boilers Страницы: 40

ECOTEC PLUS VU 80

Бренд: Vaillant Страницы: 76

Бренд: Joannes Страницы: 44

TURBO CONDENSING - 13

Бренд: Kiturami Страницы: 53

Бренд: Astra Страницы: 19

Бренд: Marco Страницы: 1

DOMESTIC SOLID FUEL BOILER

Бренд: Stropuva Страницы: 25

Mexico Super RS4100

Бренд: Ideal Boilers Страницы: 36

Mexico Super CF 3/40

Бренд: Ideal Boilers Страницы: 36

Mexico Super RS 3/40

Бренд: Ideal Boilers Страницы: 36

Бренд: Ideal Boilers Страницы: 44

Econoboil EB003

Бренд: Zip Страницы: 16

Бренд: thermital Страницы: 8

Бренд: gledhill Страницы: 44

BIASI B10 Series B3-B9

Бренд: QHT Страницы: 36

Бренд: Radiant Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды