KWB Easyfire Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 220

KWB Easyfire Скачать руководство пользователя страница 79

Page

80

IM Easyfire 10/2008

© KWB – Kraft und Wärme aus Biomasse GmbH

8 Software maintenance

8 Software maintenance

8.1.2

Software transfer to the boiler control unit

To transfer software to the boiler control unit proceed as follows:
1. Note the setting data of the controller, if this data will need to be re-entered.
2. Switch off the boiler control unit (must be de-energized for the connection)
3. Connect the null modem cable to a serial interface of your PC.
4. Connect the other end of the null model cable to the programming adapter.
5. Connect the programming adapter to the programming connector of the boiler control unit.

Connecting the programming adapter

6. Switch on the boiler controller unit again to transfer the software.
7. On the PC start the download tool for the software version that will be transferred.

Start Download

8. Select the serial port that is connected to the null model cable.

MA-Easyfire 10.2008_EN.indd 80

MA-Easyfire 10.2008_EN.indd 80

30.03.2009 13:30:13 Uhr

30.03.2009 13:30:13 Uhr

«
...
77
78
79
80
81
...
»

Содержание Easyfire





























































































































































































































Отзывы:

Нет отзывов