KVH Industries TracVision A5 Скачать руководство пользователя

Страница: 53 / 53

Step 5 - Reattach the Radome

Reattach the radome that you removed in Step 3 (on page 2).
Secure in place using the four

⁄

"-20 x

⁄

" screws.

Step 6 - Reattach the Trim Ring

Reattach the trim ring that you removed in Step 2 (on page 1).
Secure in place using the

twelve #10-32 x 1

⁄

" hex screws.

Step 7 - Pack the Antenna

Pack the antenna in its original shipping box using the original
packaging materials

(if you don’t have the original box, please request

one from KVH Technical Support at 401-847-3327)

. The “FWD”

indicator on all four corner inserts should point in the same
direction, toward the forward end of the antenna

(the end opposite

the cable connector)

The antenna is now ready for shipping.

Thank you for following

these instructions to ensure a safe shipment!

54-0217 Rev. E

TracVision A5

Ensure that you do not pinch any cables when you
reattach the radome.

Содержание TracVision A5





















































Результаты поиска

Содержание TracVision A5

Отзывы:

Похожие инструкции для TracVision A5

Бренды по названию

Популярные бренды

KVH Industries TracVision A5, Руководство по ремонту

Результаты поиска

Содержание TracVision A5

Отзывы:

Похожие инструкции для TracVision A5

Бренды по названию

Популярные бренды