Kval 990FX Скачать руководство пользователя

Страница: 46 / 96

About the Main Screen

KVAL 990-FX Operation Manual

2-16

Settings include:

•

Lock:

Press the Lock button to enable or disable the lock section machining process. If

disabled, the back section will not machine the door

•

Lock (#1-3):

Set the lock position.

•

Lock Bore:

Press the

Lock Bore

button to enable or disable the Lock Bore

•

Bolt Drill:

Press the

Bolt Drill

button to enable or disable the Bolt Drill.

•

Face Plate:

Press the

Face Plate

button to enable or disable the Face Plate.

•

Lock Backset:

indicates the backset distance for the each downloaded preset.

•

Ball Catch (Option):

Press to Enable or Disable the Ball Catch.

Lock Group

In the Lock Group, the back section machining can be manipulated. There are three

lock set-ups to use.

Содержание 990FX

































































































Результаты поиска

Содержание 990FX

Отзывы:

Похожие инструкции для 990FX

Бренды по названию

Популярные бренды

Kval 990FX, Руководство по эксплуатации

Результаты поиска

Содержание 990FX

Отзывы:

Похожие инструкции для 990FX

Бренды по названию

Популярные бренды