Kval 990FX Скачать руководство пользователя

Страница: 27 / 96

How to Download the Service Application

1-19

KVAL 990-FX Operation Manual

A pop-up window is displayed.

Accept the request to run the program.

Note:

Security settings may differ from

plant to plant. If issues occur, contact

your IT department.

The interface of the

KVAL Support App

will be dis

played. Enter your name in the

Your Name

field.

The fields are described below:

Session code:

An internal number to track this

machine. It is auto filled.

Allow Remote Control:

Program is ready to allow

technicians to access machine computer

Your Name Field:

Enter your name. The

KVAL

tech

nician will use this field to identify this machine.

Description:

Enter machine Serial number and

issue.

Indicator:

Green indicates there is a good connec

tion to the service center. If red, there could be an

issue with a LAN connection. Check the connections

in the plant.

After the

KVAL Support App

loaded and completed, call the

KVAL

Service Center(

1-800-553-5825)

and have the technician connect to

the machine computer.

Click the

Allow

button to give the

KVAL Service Technician

permis

sion to access the operator station.

We are now ready to troubleshoot.

Содержание 990FX

































































































Результаты поиска

Содержание 990FX

Отзывы:

Похожие инструкции для 990FX

Бренды по названию

Популярные бренды

Kval 990FX, Руководство по эксплуатации

Результаты поиска

Содержание 990FX

Отзывы:

Похожие инструкции для 990FX

Бренды по названию

Популярные бренды