Kval 990FX Скачать руководство пользователя

Страница: 48 / 96

About Manual Operation

KVAL 990-FX Operation Manual

2-18

Width Adjust

•

Open

Press and

hold

the

Open

button to open the width adjust car

riage. To stop the carriage, release the button.

Note:

The carriage will also stop if the positive travel limit eye is activated.

•

Close:

Press and

hold

the

Close

button to close the width adjust car

riage. To stop the carriage, release the button.

Note:

The carriage will also stop if the negative travel limit eye is activated.

Feed Manual Control

Feed:

•

Reverse:

Press and

hold

the

Reverse

button

reverse the feed of the door. To stop the feed,

release the button.

•

Forward:

Press and

hold

the

Forward

button to

move the door feed forward. To stop the feed,

release the button.

•

Normal Speed:

Press and

hold

the

Normal

Speed

button to slow speed. To return to previous speed, release the button.

Clamp and Stop:

•

Stop:

Press the

Stop

button to extend or retract the appropriate door stop.

•

Clamp

Press

Clamp

to activate the cylinders that clamp the door.

Содержание 990FX

































































































Результаты поиска

Содержание 990FX

Отзывы:

Похожие инструкции для 990FX

Бренды по названию

Популярные бренды

Kval 990FX, Руководство по эксплуатации

Результаты поиска

Содержание 990FX

Отзывы:

Похожие инструкции для 990FX

Бренды по названию

Популярные бренды