Kval 990FX Скачать руководство пользователя

Страница: 33 / 96

Initial Powering Operations for the 990-FX Line

2-3

KVAL 990-FX Operation Manual

Home the 990-FX

The

990-FX

must go through a homing routine before any operations are performed. The homing

routine sets a zero reference from which the

990-FX

measures its movement and cutting process.

If power is lost or the

990-FX

is re-set, the homing routine must be performed again to reset the

zero reference
Press the

Home

button on the

Main Screen

touch screen.

Initiate the

Hinge Loaded

to act as a Reset.

Note:

This process is a safety precaution to ensure the no personnel is in the machine staging area.

Push the

Hinge

Loaded Button

All lights on the status light panels on the electrical

box should be illuminated.

Note:

If a status light does not turn on during the power up pro

cess, see

the trouble shooting chapter in the Service Manual.

The machine will move to the home position at the

in-feed end of the machine.

The machine will then move to about the middle

of its travel.

The

990-FX

is now ready for work.

Содержание 990FX

































































































Результаты поиска

Содержание 990FX

Отзывы:

Похожие инструкции для 990FX

Бренды по названию

Популярные бренды

Kval 990FX, Руководство по эксплуатации

Результаты поиска

Содержание 990FX

Отзывы:

Похожие инструкции для 990FX

Бренды по названию

Популярные бренды