Kval 990FX Скачать руководство пользователя | Manualshive

Страница: 29 / 96

background image

Safety Sign-Off Sheet

1-21

KVAL 990-FX Operation Manual

Safety Sign-Off Sheet

Machine Model Number:_____________________________

A Note to the Operator

This machine can help you be highly productive only if you understand how to use it properly and

follow the safe operating practices described in this document and the machine’s manual. If you

do not understand the machine’s proper operation or ignore the safe operating practices, this

machine can hurt or kill you. It’s in your best interest to safely and properly operate this machine.

Personnel Safety Concerns:

•  I have been properly trained in the operation of this machine.
•  I will always wear ear protection when operating this machine.
•  I will always wear eye protection when operating this machine.
•  I will never wear loose clothing or gloves when operating this machine.
•  I will watch out for other people. Make sure everyone is clear of this machine

before operation.

• I will always follow my company’s safety procedures. I have read and understand

these guidelines.

Machine Safety Concerns:

• I have been given a tour of the machine and understand all the safety labels, E-

Stops and the actions to take in case of an emergency.

•  I will make sure all guards are in place before operation
•  I will turn off the compressed air, before loading hardware (staples, screws, etc)
•  I will turn off the electrical power, for setup
•  If the machine should operate in an unexpected manner stop production I will

immediately and notify a manager, a supervisor, or a qualified service technician.

I have read and understand this document and agree to operate this machine in a safe man

-

ner as described above.
Employee

Name (print):

___________________

Signature:

__________________

Date:

____/____/____

Supervisor/Safety Officer/Trainer
Name (print):

__________________

Signature:

__________________

Date:

____/____/___

Note:

It is recommended you make a copy of this sheet for new operators. If a copy is

needed, you may download a PDF at the

KVAL

website (http://www.kvalinc.com).

You may also contact our Service Department at (800) 553-5825 or email at ser

-

[email protected].

«
...
27
28
29
30
31
...
»

Содержание 990FX

































































































Отзывы:

Нет отзывов

Похожие инструкции для 990FX

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Labnet Страницы: 2

Бренд: MacDon Страницы: 2

Бренд: MacDon Страницы: 214

Бренд: MacDon Страницы: 32

Бренд: YSI Страницы: 70

Бренд: jcb Страницы: 41

Бренд: T-Rex Страницы: 13

Бренд: Water Witch Страницы: 2

Бренд: Falltech Страницы: 48

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: Hakko Electronics Страницы: 8

Professional HS 8

Бренд: Hailo Страницы: 5

Бренд: Hainbuch Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды