KUHN FC243RGII Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 112

background image

FC243RGII

18

4. - Safety

KN041BGB A

Mower conditioner

4.2.10 PTO shaft

Use only PTO shafts supplied with the machine or recommended by the machine manufacturer.

The protective shield of the tractor PTO stub, the PTO shaft guards and the protective shield of the machine
input shaft must always be in place and in good condition.

Make sure that the PTO shaft guards are secured with the safety chains provided. Check that the PTO shaft
guard can turn freely a full rotation independent of the shaft.

Any worn or damaged guards must be replaced immediately. A worn guard or an unprotected PTO shaft
can cause a serious or even a lethal accident.

Do not wear loose clothing that could be caught in
the rotating PTO shaft.

Before attaching or removing a PTO shaft, or before doing any work on the machine, disengage the PTO
drive, turn off the engine, remove ignition key and wait for all moving parts to come to a complete stop.

If the primary PTO shaft is equipped with a torque limiter or a free wheel, these must be fitted on the machine
side.

Ensure that the PTO shaft is always correctly fitted and locked into place.

Before connecting the PTO shaft, ensure that the PTO speed (rotational frequency) and direction of rotation
are in line with the machine manufacturer's recommendations.

Before engaging the PTO drive, make sure that there are no people or animals near the machine. Never
engage the PTO drive when the tractor engine is stopped.

«
...
18
19
20
21
22
...
»

Содержание FC243RGII

















































































































Отзывы:

Нет отзывов

Похожие инструкции для FC243RGII

Бренд: SALUDA MEDICAL Страницы: 61

Бренд: Fisher Scientific Страницы: 42

Бренд: B&G Страницы: 3

Бренд: Eastern Jungle Gym Страницы: 17

Бренд: Vahle Страницы: 96

Бренд: GALBIATI Страницы: 20

Бренд: Banfer Страницы: 6

Бренд: vanEE Страницы: 52

Бренд: Caddon Hives Страницы: 3

Бренд: Mandam Страницы: 9

Бренд: Farmi Forest Corporation Страницы: 32

Бренд: Hammer Strength Страницы: 18

Бренд: Velp Scientifica Страницы: 12

Бренд: Yamaha Страницы: 24

Бренд: J&M Страницы: 33

Бренд: K-9 Lights Страницы: 12

Бренд: K'Nex Education Страницы: 2

TRAKTOR KONTROL S4

Бренд: Native Instruments Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды