KUHN ATHENOR 6070 Скачать руководство пользователя страница 70

Страница: 70 / 98

Silo unloader - Straw spreader - Mixer - Distributor

ATHENOR 6070

Optional equipment

- Start the tractor, then gradually engage the power

take-off until the pump turns.

- Check that all machine functions are operational.

Make sure the pump flanges and various hydraulic
connections are tight.

- With the gear lever, the hydraulic unit can be used in

three ways:
• In neutral, without engaging the blower, for all

loading operations.

• At a blower speed of 270 min

-1

for distribution.

• At a blower speed of 540 min

-1

for straw feeding.

Maintenance

- Follow the safety regulations concerning machine

servicing.

- Check the oil level in the tank periodically. The oil level

must not fall below the upper 1/3 on the indicator.

- Change the hydraulic oil every 1500 hours.
- Replace the filter cartridge after the first 50 hours of

operation, then every 500 hours. For that purpose::
• Unscrew the cap.
• Take the filter handle and remove the filter-bowl

unit.

• To remove the filter:Turn the handle a quarter turn

anticlockwise and remove the filter from its
cartridge.

• Clean the bowl.
• Put in a new filter and lock its position, turning it a

quarter turn clockwise.

• Replace the cap and reposition the seal properly to

ensure tightness.

Under no circumstances must you use the
tractor power take-off 1000 min

-1

Содержание ATHENOR 6070



































































































Результаты поиска

Содержание ATHENOR 6070

Отзывы:

Похожие инструкции для ATHENOR 6070

Бренды по названию

Популярные бренды

KUHN ATHENOR 6070, Руководство оператора

Результаты поиска

Содержание ATHENOR 6070

Отзывы:

Похожие инструкции для ATHENOR 6070

Бренды по названию

Популярные бренды