KUHN ATHENOR 6070 Скачать руководство пользователя страница 65

Страница: 65 / 98

Instructions for work

Silo unloader - Straw spreader - Mixer - Distributor

ATHENOR 6070

Hay and haylage

- Start up the tractor PTO and bring the engine up to

nominal speed.

- Switch the tractor's hydraulic distributor to continuous

pumping.

- Point the delivery chute downwards so that the forage

should be properly channelled to the ground or into a
trough.

- Start up the beater bar using the clutch (until the

indicator lamp lights up, if you have electric controls).

- To distribute the product, start the conveyor running

forward and adjust the speed:
• Set the conveyor to forward.
• Adjust its speed.

- The conveyor speed is set at the control box

according to the forward speed and product
distribution criteria and the type of product.

- When the distribution is finished:

• Retract the arm and hook as far as they will go.
• Stop the conveyor and disengage the beater bar.
• Disengage the bale separator.
• Close the distribution chute.
• Disengage tractor PTO.

Never distribute hay or haylage with hooks fitted
to the beater bar.

Содержание ATHENOR 6070



































































































Результаты поиска

Содержание ATHENOR 6070

Отзывы:

Похожие инструкции для ATHENOR 6070

Бренды по названию

Популярные бренды

KUHN ATHENOR 6070, Руководство оператора

Результаты поиска

Содержание ATHENOR 6070

Отзывы:

Похожие инструкции для ATHENOR 6070

Бренды по названию

Популярные бренды