KUHN ATHENOR 6070 Скачать руководство пользователя страница 68

Страница: 68 / 98

Silo unloader - Straw spreader - Mixer - Distributor

ATHENOR 6070

Instructions for work

Operating tips

- To blow the straw regularly, the bale must remain in

permanent contact with the beater bar, but must not
be blocked too hard by the gate.

- Lift the back of the machine slightly to avoid the bale

being thrown to the back of the beater bar.

- During straw blowing, adjust the height of the body in

order to:
• keep round bales up against the beater bar when

the product requires little power.

• facilitate the rotation of round bales against the

beater bar when the product is tougher.

- To improve product feed into the blower, up to 3 hooks

can be mounted on the beater bar in place of the
sections.

Keep an angle of 120° between the hooks.
Never distribute hay or haylage with hooks fitted
to the beater bar.

You are strongly recommended to spread straw
after distributing feed to the animals: this helps
clean and dry the machine (straw absorbs silage
acids) and thereby limit corrosion of the machine
by acid attack..

To spread straw in stalls, use a turbine rotation
speed of 270 min

-1

Содержание ATHENOR 6070



































































































Результаты поиска

Содержание ATHENOR 6070

Отзывы:

Похожие инструкции для ATHENOR 6070

Бренды по названию

Популярные бренды

KUHN ATHENOR 6070, Руководство оператора

Результаты поиска

Содержание ATHENOR 6070

Отзывы:

Похожие инструкции для ATHENOR 6070

Бренды по названию

Популярные бренды