KUHN ATHENOR 6070 Скачать руководство пользователя страница 66

Страница: 66 / 98

Silo unloader - Straw spreader - Mixer - Distributor

ATHENOR 6070

Instructions for work

Operating tips

- To facilitate feeding the turbine from the bale

separator, let the bale turn freely under the action of
the separators.

- Reduce engine speed when feeding is over to limit

projections.

During feeding, raise the back of the body in order to:

• keep round bales up against the beater bar when

the product requires little power.

• facilitate the rotation of round bales against the

beater bar when the product is tougher.

- The conveyor speed is set at the control box

according to the forward speed and product
distribution criteria and the type of product.

- If you are using the equipment with 2 round bales,

make sure the first bale is turning freely before
engaging the separators. Reverse the conveyor if
necessary.

Содержание ATHENOR 6070



































































































Результаты поиска

Содержание ATHENOR 6070

Отзывы:

Похожие инструкции для ATHENOR 6070

Бренды по названию

Популярные бренды

KUHN ATHENOR 6070, Руководство оператора

Результаты поиска

Содержание ATHENOR 6070

Отзывы:

Похожие инструкции для ATHENOR 6070

Бренды по названию

Популярные бренды