KUHN ATHENOR 6070 Скачать руководство пользователя страница 18

Страница: 18 / 98

Silo unloader - Straw spreader - Mixer - Distributor

ATHENOR 6070

Safety

Precautions and prevention of fire risk

Your machine works with moving parts (bale

separator(s), turbine) and highly inflammable products.

There is therefore a real risk of fire resulting from:

- Overheating of the power takeoff friction limiter.

Please do not use this limiter excessively. If smoke
issues from the transmission, stop the machine
immediately and leave the limiter to cool outside the
buildings.

- Winding strink or products at the ends of the bale

separator(s).

- Each time, before using the machine, check the ends

of the bale separator(s) to remove products which
have become wound round or have accumulated in
this area.

- Worn bearing. Grease bearings regularly and check

their condition.

- Sparks caused by pebbles or metal objects in the

straw.

It is highly recommended to have an extinguisher which

has been checked and maintained, on your tractor.
Recommended types: sprayed water + additive, ABC
powder.

It is strictly prohibited to use your machine stationary

inside a building.

Содержание ATHENOR 6070



































































































Результаты поиска

Содержание ATHENOR 6070

Отзывы:

Похожие инструкции для ATHENOR 6070

Бренды по названию

Популярные бренды

KUHN ATHENOR 6070, Руководство оператора

Результаты поиска

Содержание ATHENOR 6070

Отзывы:

Похожие инструкции для ATHENOR 6070

Бренды по названию

Популярные бренды