KSB UPA Скачать руководство пользователя страница 3

Страница: 3 / 98

Contents

3 of 98

UPA / UPA S

Contents

General.................................................................................................................................................... 6

1.1

Principles ........................................................................................................................................................... 6

1.2

Target group..................................................................................................................................................... 6

1.3

Other applicable documentation .................................................................................................................... 7

1.4

Symbols ............................................................................................................................................................. 7

1.5

Key to safety symbols/markings....................................................................................................................... 8

Safety ...................................................................................................................................................... 9

2.1

General.............................................................................................................................................................. 9

2.2

Intended use ..................................................................................................................................................... 9

2.3

Personnel qualification and training............................................................................................................... 9

2.4

Consequences and risks caused by non-compliance with this manual ....................................................... 10

2.5

Safety awareness ............................................................................................................................................ 10

2.6

Safety information for the operator/user ..................................................................................................... 10

2.7

Safety information for maintenance, inspection and installation .............................................................. 10

2.8

Unauthorised modes of operation ................................................................................................................ 11

2.9

Magnet rotor .................................................................................................................................................. 11

Transport/Storage/Disposal ................................................................................................................ 12

3.1

Checking the condition upon delivery .......................................................................................................... 12

3.2

Transport......................................................................................................................................................... 12

3.3

Pulling the pump/motor/pump set upright .................................................................................................. 14

3.4

Storage/preservation ...................................................................................................................................... 15

3.5

Return to supplier........................................................................................................................................... 16

3.6

Disposal ........................................................................................................................................................... 17

Description of the Pump (Set) ............................................................................................................. 18

4.1

General description ........................................................................................................................................ 18

4.2

Product information....................................................................................................................................... 18
4.2.1

Product information as per Regulation No. 1907/2006 (REACH) .................................................... 18

4.2.2

Product information as per Regulation No. 547/2012 (for 4" and 6" water pumps) implementing

"Ecodesign" Directive 2009/125/EC................................................................................................... 18

4.3

Designation..................................................................................................................................................... 19
4.3.1

Designation used for pump sets with VdS certification .................................................................. 20

4.4

VdS approval numbers ................................................................................................................................... 20

4.5

Name plate...................................................................................................................................................... 21

4.6

Design details.................................................................................................................................................. 22

4.7

Configuration and function........................................................................................................................... 23

4.8

Scope of supply............................................................................................................................................... 24

4.9

Dimensions and weights ................................................................................................................................ 24

Installation at Site ................................................................................................................................ 25

5.1

General information/Safety regulations ....................................................................................................... 25

5.2

Preparing the installation .............................................................................................................................. 26
5.2.1

Checking the installation conditions ................................................................................................ 26

5.2.2

Checking the installation position ................................................................................................... 27

5.2.3

Checking the motor fill...................................................................................................................... 28

5.2.4

Installing water storage tanks........................................................................................................... 29

5.2.5

Preventing backflow.......................................................................................................................... 30

5.2.6

Calculating the total weight ............................................................................................................. 30

5.2.7

Electric wiring..................................................................................................................................... 31

5.2.8

Measuring the insulation resistance ................................................................................................. 33

5.3

Installing the pump set in a vertical position ............................................................................................... 34
5.3.1

Attaching the cable ties..................................................................................................................... 36

5.4

Installing the pump set in a horizontal position .......................................................................................... 38
5.4.1

Mounting the pump set on pedestals .............................................................................................. 39

5.4.2

Installing the pump set on support frame and pedestal................................................................. 39

Содержание UPA



































































































Результаты поиска

Содержание UPA

Отзывы:

Похожие инструкции для UPA

Бренды по названию

Популярные бренды

KSB UPA, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UPA

Отзывы:

Похожие инструкции для UPA

Бренды по названию

Популярные бренды