KSB UPA Скачать руководство пользователя страница 25

Страница: 25 / 98

5 Installation at Site

25 of 98

UPA / UPA S

3400.86/17-EN

5 Installation at Site

5.1 General information/Safety regulations

DANGER

Using damaged cables in a well

Electric shock!

▷

Do not kink the electric cable.

▷

Observe the minimum bending radius

10)

of the electric cable. Do not drag the

cable over sharp edges.

▷

Use cable ties or other suitable fasteners to fasten the electric cables to the riser
or piping every 3 m.

▷

Do not use any tools, equipment or accessories with sharp edges (e.g. sharp-
edged pipe sockets) for installation.

WARNING

Pump set falling into the well

Risk of injury from uncontrolled movements of electric cables!

Damage to the pump set and the well!

▷

Store electric cables safely. Keep at a safe distance during installation.

▷

Secure the pump set during the entire installation procedure.

▷

Dimension any securing devices (supporting clamps, supports, etc.) so that they
can carry all weights during the installation.

WARNING

Persons could fall into unsecured wells/reservoirs/tanks

Risk of personal injury!

▷

During installation work, take suitable precautions to protect anyone from
falling into an open well/reservoir/tank.

▷

Suitably fence off the work area.

WARNING

Improper handling when placing the pump set in a vertical/horizontal position

Personal injury and damage to property!

▷

Use one or two pieces of lifting equipment, depending on the pump (set) size.

▷

Use appropriate means to secure the pump set against tilting, tipping over or
rolling off.

▷

Maintain a safe distance during lifting operations (load may swing when being
lifted).

▷

Use additional supports for the transport holder to secure it against tilting.

WARNING

Incorrect handling of the power cable

Personal injury and damage to property!

▷

Secure the power cable against falling down.

Observe the cable manufacturer's documentation, DIN VDE 0298-3 and/or the general arrangement drawing.

Содержание UPA



































































































Результаты поиска

Содержание UPA

Отзывы:

Похожие инструкции для UPA

Бренды по названию

Популярные бренды

KSB UPA, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UPA

Отзывы:

Похожие инструкции для UPA

Бренды по названию

Популярные бренды