KSB UPA Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 98

background image

3 Transport/Storage/Disposal

16 of 98

UPA / UPA S

3400.86/17-EN

5.

Protected against dirt and dust

6.

Protected against freezing

7.

Protected against vermin

For further information on storing the pump set after it has been in use see
(

Section 7.5, Page 74) .

3.5 Return to supplier

CAUTION

Ambient temperature below the specified minimum

Danger of frost!

▷

Never subject the pump set to ambient temperatures which are lower than
those permitted for the drinking water/antifreeze mixture provided.

1. Clean the pump set properly from the outside.

2. Flush and clean the pump, particularly if it has been used for handling noxious,

explosive or other hazardous fluids.

3. If the pump has handled fluids whose residues could lead to corrosion damage

in the presence of atmospheric humidity or could ignite upon contact with
oxygen also neutralise the pump and blow through with anhydrous inert gas to
ensure drying.

4. Always fully complete and enclose a certificate of decontamination when

returning the pump (set).
Indicate any safety measures and decontamination measures taken.
(

Section 11, Page 94)

DANGER

Strong magnetic field in the area of the magnet rotor of
UMA-S 150, UMA-S 200 or UMA-S 250 submersible motors

Danger of death for persons with pacemaker!

Interference with magnetic data carriers, electronic devices, components and
instruments!

Uncontrolled magnetic attraction forces between magnet-equipped components,
tools or similar!

▷

If the submersible motor is to be returned to the supplier, attach the adhesive
safety notice to the submersible motor. The safety notice must be clearly visible.

UMA-S 150, UMA-S 200 or UMA-S 250 motors as well as pump sets containing these
motors must be clearly marked to identify the motor as a synchronous motor with
permanent magnets.

For this purpose, a “synchronous motor” warning sticker is

supplied with the delivery, which must be attached to the motor if it is to be
returned to the supplier.

«
...
14
15
16
17
18
...
»

Содержание UPA



































































































Отзывы:

Нет отзывов

Похожие инструкции для UPA

Бренд: Canon Страницы: 2

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: Hankscraft Runxin Страницы: 53

Бренд: Gardena Страницы: 16

Бренд: MADRIX Страницы: 28

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 35

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 73

Бренд: Eaton Страницы: 4

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 14

Бренд: Eaton Страницы: 36

CEmarking RCX221

Бренд: Yamaha Страницы: 468

Бренд: Yoshitake Страницы: 4

Бренд: YOKOGAWA Страницы: 20

UTAdvanced UT32A

Бренд: YOKOGAWA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды