KSB UPA Скачать руководство пользователя страница 33

Страница: 33 / 98

5 Installation at Site

33 of 98

UPA / UPA S

3400.86/17-EN

5.2.8 Measuring the insulation resistance

DANGER

Hazardous voltage during and after measurement

Danger of death from electric shock!

▷

Do not touch the contact points during and immediately after measurement.

▷

Insulation resistance measurement must be effected by a trained electrician
only.

Measure the insulation resistance prior to installation and prior to connection to
the power supply.

Insulation resistance measurement must be effected by a trained electrician only.

Prior to the measurement, ensure compliance with the operating manual of the
insulation resistance measuring device.

An insulation resistance measuring device with a measuring voltage of 1000 V DC
is available.

The contact points are clean and dry.

1. Measurement period: 1 minute

13)

2. Recommendation: insulation resistance at 20 °C - 30 °C: > 200 MOhm

14)

Rinsul
(MΩ)

M 3~

Lorem ipsum

Fig. 8:

Insulation resistance measurement, 1 power cable

Risol

(MΩ)

M 3~

Fig. 9:

Insulation resistance measurement, 2 power cables (open)

The measured value must be steady. A longer measurement period might be needed for larger cable cross-
sections.

The insulation resistance depends on the cable type and cable length.

Содержание UPA



































































































Результаты поиска

Содержание UPA

Отзывы:

Похожие инструкции для UPA

Бренды по названию

Популярные бренды

KSB UPA, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UPA

Отзывы:

Похожие инструкции для UPA

Бренды по названию

Популярные бренды