KSB UPA Скачать руководство пользователя страница 29

Страница: 29 / 98

5 Installation at Site

29 of 98

UPA / UPA S

3400.86/17-EN

Motor type
series

Supplied
condition

Information sticker

Motor fill check required

See Section

UMA-S 150

Filled

Required if the motor has been
stored or out of service for more than
1 year

(

Section 7.4.2, Page 68)

UMA 200

Filled

Required if the motor has been
stored or out of service for more than
1 year

(

Section 7.4.2, Page 68)

UMA-S 200

Filled

Required if the motor has been
stored or out of service for more than
1 year

(

Section 7.4.2, Page 68)

UMA 250

Filled

Required if the motor has been
stored or out of service for more than
1 year

(

Section 7.4.2, Page 68)

UMA-S 250

Filled

Required if the motor has been
stored or out of service for more than
1 year

(

Section 7.4.2, Page 68)

UMA 300

Filled

Green information sticker Required

(

Section 7.4.3, Page 72)

Unfilled

Red information sticker

14D

Filled

Green information sticker Required

(

Section 7.4.3, Page 72)

Unfilled

Red information sticker

NOTE

The loss of a few drops of liquid fill will not impair the motor function. If any larger
amounts of leakage are suspected, the motor fill must definitely be checked.

5.2.4 Installing water storage tanks

If the pump set is intended for horizontal installation, submersible motors UMA 300
or 14D require a water reservoir.

741

411.51

903.53

59-33

411.51

Fig. 7:

Installing water

storage tanks

The motor has been placed down in a horizontal position on a level and solid
surface. It has been secured against rolling off.

Position the motor with the connections for the water storage tanks at the
highest point.

The water storage tanks are on hand.

The motor fill has been checked with the motor in a vertical position.

Suitable liquid for topping up the motor fill has been prepared.

1. Remove the screw plugs from the top and bottom of the stator case. Remove

the joint rings.

2. Insert the water storage tanks (59-33) with new joint rings (411.51) into the

stator and screw them in tightly.

3. Fill the water storage tanks with the specified liquid fill until they overflow.

4. Close both water storage tanks with a screw plug with integrated vent valve

(741) and joint ring (411.51).

Содержание UPA



































































































Результаты поиска

Содержание UPA

Отзывы:

Похожие инструкции для UPA

Бренды по названию

Популярные бренды

KSB UPA, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UPA

Отзывы:

Похожие инструкции для UPA

Бренды по названию

Популярные бренды